Implement Quick Coupling Assembly
710 • 728 • 738 • 740 • 780HY • 614 • 615 • 618 • 630 • 630WS
This two-part coupler allows implements to be changed quickly and without the need for tools - simply lift the red lever to remove the implement.
Additional Coupling
Where the power unit is using the Implement Quick Coupling Assembly this is required for all further powered implements.
Blank Coupling
Where the power unit is using the Implement Quick Coupling Assembly this is required for all further non-powered implements.
Additional Coupling - BCS 660HY and 750
660HY • 750
This coupler is for additional implements for the BCS 660HY and BCS 750 which have their own specific built-in quick coupling.
Implement Extension
710 • 728 • 738 • 740 • 750 • 780HY • 614 • 615 • 618 • 630 • 630WS • 660HY
Add an extra 8cm distance between the implement and power unit - ideal for when larger wheels are fitted, or balance is required.
New Machine to Old Implement Coupler
This coupler converts the current 3-dog machine PTO to operate older implements with a spline shaft PTO.
Old Machine to New Implement Coupler
This coupler will convert the older spline shaft machine PTO to operate current implements with a 3-dog PTO.
Counterbalance Weight Kit
The counterbalance weight attaches to the engine protection to help balance the power unit with heavier implements.
Pneumatic Wheels
4.00 x 8 • 4.00 x 10 • 5.00 x 10 • 6.50 x 12
All BCS power units are fitted with these pneumatic wheels. These are available in a range of sizes to fit different power units.
Lug Wheels
8.00 x 10
A wider profile and deeper tread than the standard pneumatic wheels offer additional traction and stability.
Turf Wheels
A wider, low compaction profile featuring a turf saver tread ideal for use on lawns and turfed areas.
Flotation Wheels
11.00 x 8
A widened profile distributes the load and traction on a much wider contact surface ideal for water-logged or boggy ground.
Twin Wheel Kit
4.00 x 10 • 5.00 x 10 • 6.50 x 12
An additional set of tyres and all the fixings to enable single wheels to be doubled-up. Ideal on slopes where extra stability is required.
Steel Bank Wheels
5.00 x 10
When combined with pneumatic wheels, these wide metal cage wheels provide extra traction on sloping banks.
Spade Lug Wheels
43cm • 49cm • 58cm
The metal crosspieces on the spade lug wheels help provide additional traction, particularly when ploughing or ridging.
Twinning Rings
49cm
Double the width of the 49cm (19") spade lug wheels to further improve traction in extreme conditions.
Wheel Spacers
6cm
Extend the wheel width by 6cm each side when additional stability is required. These can be doubled-up to add up to 12cm each side.
Adjustable Wheel Spacers
2½cm-15cm • 2½cm-25cm
Where additional stability is required these can be added to the wheels and adjusted as required. They offer more width than the fixed spacers.
Wheel Weights
11kg • 15kg • 34kg
Where extra traction is required these can be bolted to the wheel hubs to increase the tractor weight.
Scythe Cutter Bar Weight
12kg
Add this weight to the scythe cutter bar transmission to improve balance when fitted to larger power units.
Rotavator Transport Wheel
This very useful accessory raises the rotavator off the ground to help when transporting from storage to working area.
Snow Plough Castor Wheels
Improve manouevrability of the snow plough by replacing the saucer-shaped skids with these wheels.
Snow Plough Soft Blade Kit
For use on sensitive areas this helps to reduce potential damage that could be caused the standard metal blade.
Implement Weight
Add this weight to implements that need to be balanced with the power unit. Suitable for Snow Blower, Dozer Blade, Snow Plough, and Wheel Barrow.
Tractor PTO Coupler
Convert the BCS PTO to a 6-spline allowing the power unit to operate certain low power, stationary implements.
PTO Multiplier
Increase the PTO speed of the BCS power unit from 990rpm to 3600rpm in order to operate attachments that need a faster operating speed.
